235x235mm Ender 3 Bed Magnetic Flexible Heated Bed PEI Sheet

Roberto Furlan: ottimo

Italy on Aug 28, 2023

Carlos Rios Blas: Imprescindible si tienes una ender 3 s1, la que viene de serie con la impresora es muy mala, con esta placa mejora muchísimo adherencia de las pieza y luego son muy fscil de despegar.

Spain on Aug 24, 2023

Nagol: Easy to install on ender 3. Only negative is that this requires installing a large magnetic strip to heated plate with adhesive. If you were planning to replace the plate or remove it the is will cover the screw holes on the plate. You could always cut these out before instillation but that might make the bed more flexible in those spots.

United States on Aug 17, 2023

Andrew Smith: I bought this to replace the stock one from my under S1 Pro that had begun to get worn out. It's awesome! Many of these are not double-sided but this one has a coating on the smooth side as well. I'd purchase this over a oem replacement personally if I ever need one again.

United States on Aug 14, 2023

Jul: Installé sur une ender 3 s1, il fait bien le taf. Attention tout de même, l'adhérence de la première couche peut être problématique (il doit être bien dégraissé et dépoussiéré), j'utilise de la colle en stick pour être sûr de réussir mon impression.

France on Aug 13, 2023

Isaiah Benitez: As soon as you get your Ender 3, please buy this, you won't regret it! Hands down the best surface to print on, I have had zero adhesion problems and I've been using mine for 6 months. At the same time, it leaves a nice clean edge on all your prints. 10/10 will buy over and over again!

United States on Aug 09, 2023

Diederick: Glad geeft heel mooi resultaat en als de print wat moeilijker is werkt de structuur zijde nog steeds goed.

Netherlands on Jul 24, 2023

Ragner Azenos: Ive been through 2 pei beds, this is my third, first two were junk. bought this and couldn't be happier. First month of use it worked flawlessly. when the bed would cool down the print would just be sitting there waiting for me to pick up. It stuck to the bed first time with no issues every time. Now after a month i am having a little issue with adhesion, but i used a glue stick and after that ive had no more bed adhesion issues

United States on Jul 22, 2023

Carlos Paz: Me ha encantado me facilita muchísimo despegar las impresiones de esta superficie solo curveandolo.
Aun no uso la parte lisa, pero se ve que dará otro acabado a mi piezas.
Saludos.

Mexico on Jul 15, 2023

Charles LeoneCharles Leone: After 3 years and hundreds of prints, the Ultrabase on my Anycubic Mega S started to wear out. Glue stick and painters tape helped remedy models not sticking, so did one the large adhesive sticker-styling built plates that came with some Overture PLA but all three methods resulted in prints that were very difficult to remove without a risk of damaging them. I decided to try a PEI build plate and after some minor modifications got this built installed and I've never been happier with the quality of prints and the ease of removal. The smooth side results in a first layer that's nearly flawless, close to using a bare glass plate and the textured side gives the print a superb finish that hides the first layer lines. Finished prints are easily removed whether cool or not. Cooled prints can usually be removed without removing the build plate but if you're printing round the clock like sometimes do, removing prints that are still warm is as easy as slightly bending the plate while it's still on the printer or removing the plate and flexing it. Depending on the model, I find I may need to add a negative z-offset(-0.25mm) in cura when slicing in order to get a proper first layer...

United States on Jan 24, 2023