Sunex 2 Ton Low Rider Steel Service Jack with 6602LP Model

KCJP: Solid, great height and extreme low profile. Very heavy though as expected.

United States on Sep 26, 2023

James West: I bought this to use with my 2001 & 2020 corvettes. I needed something very low profile that would work well with jacking pucks. Sunex screams quality, very well made easy to move and I don't worry that I'll damage my cars with a cheap jack. You get what you pay for and it's well worth the price.

United States on Aug 09, 2023

Henry Jorge: Works perfectly and it's an excellent jack. Heavy duty, I have no complaints.

United States on Jun 21, 2023

Clayton B.: The Jack is nice and quality seems good, it’s smooth although we haven’t lifted a car yet the jacks lowest setting is 3” when it’s advertised as a 2.75”, the reason we bought it.
Also disappointed there is no rubber saddle like most jacks in this price range have.

Canada on May 19, 2023

Martin Quesnel: 100% satisfait, rabais incroyable pour boîte endommagée, 400$ d’économie. Meilleur jack j’ai essayé dans ma vie

Canada on Apr 29, 2023

Derek: My best friend since I got it. I have a quite low car and absolutely needed a long range low jack like this. 4 stars just because of the price which is a bit high but still worth it if you need a low jack. minimum height is 2.75'' and has a long range to be able to jack from the middle of the car(differential, sub-frame).

Canada on May 06, 2020

Mugwump: Arrived today. Box and jack in perfect condition. No structural or cosmetic flaws. Very heavy but rolls smoothly. Be careful removing the wire which holds the pistons in and yoke down for shipping. No hints in instructions on how to remove it safely (I cut it with a die grinder with a cutting wheel but from behind with the mechanism pointing at a wall and wearing a full face safety shield in case they were held in with more force than I expected...it wasn't). Clear process in manual and online to remove any trapped air. Rolls easily and the handle and mechanism works smoothly. .

I measured the minimum position at more than 2 3/4", which is a bit disappointing. it was almost 3" ( 2 15/16) across the tops of the "tabs" on the saddle, and identical to my old jack. While it might be a bit lower between the tabs that is an unrealistic measurement as it is the tabs which will make the contact with the lift point on the vehicle. The maximum lift was higher than spec at 24 5/8". The low rise section, measured from the center of the saddle, was 16".

I tested operation on a light car (1220 pounds) in my shop and it took leass effort than my old jack. It also worked smoothly...

United States on Dec 21, 2019

Client d'Amazon: Bonne qualité

Canada on Aug 19, 2019

howard colp: I bought many floor jacks over the years . But this is by far the best one

Canada on Feb 28, 2018

welder314: This is a very good quality jack. It is made in China, but it does not look or feel cheap. You can see this in the detail, for example the set screw for the handle uses a large diameter thread and it's lathe turned on the end. The quick-disconnect button on the handle is thick steel and is solid. Not that it affects function, but the paint is smooth, no drips or runs, and there were no sharp edges or poor quality stampings. All the welds looked good. This is not the same one that looks identical and sold by the store with initials H.F.; I've had hand-on experience with that one and I can say that it IS cheap. This does not reek with the odor of cheap tools either (I know the smell doesn't matter but you know how everything at H.F. smells...).

To me this is not a heavy jack, in fact it seems about on par with most similar sized steel jacks. When it arrived (on a pallet), I just opened the box and lifted it out. I guess it depends on what you are used to. It rolls easily even on my somewhat rough and sloped (5 degree) driveway. It doesn't get hung up any more than my other shorter jacks; it does sit low, and of course will drag on concrete boundaries, etc. Obviously if you're...

United States on Oct 18, 2016