Campbell Hausfeld 3-in-1 Tire Inflator Gun with Gun Lock for Convenient Air Pressure Maintenance

Steven Brenner: Works great as long as there is enough room for the hose. Not so great when the valve stem is on a small wheel and the stem points straight up into the wheel instead of out towards the side.

United States on Dec 03, 2023

Peter: I love this pressure guage. My last one got dropped and deformed the guage so I jist had to get another. So convenient having the guage, nozzle and air control all on one compact unit. Makes filling tires so much easier.

Canada on May 04, 2023

Aaron: Easy to use, clamps on to valve stem and the pressure gauge is accurate

Canada on Apr 24, 2021

Giok : that's exactly what I was looking for. good quality, accurate, it works perfectly!

Canada on Oct 22, 2020

Jalil: Es bastante preciso y facilita mucho la correcta lectura y llenado de aire en los neumáticos. Es muy recomendable tener uno en casa.

Mexico on Jan 16, 2020

arturo flores garcia: Muy cómodo de usar, lo probamos para las llantas del automóvil y de la moto, fusiona muy bien, fácil de leer los PSI y de dejar escapar aire si uno se pasa de presión.

Mexico on Apr 14, 2018

Sci-Fi Fan: If you read the reviews- lots of people complain about the tire chuck not working properly. When my unit came- I had the same problem on my 2014 car. I couldn't push the tire chuck down far enough onto the tire's valve stem to engage the pin valve to let air into the tire. Tried on my other two cars... didn't work on them either.
I was ready to send the unit back for a refund- when I noticed you could take the tire chuck apart, so with nothing to loose I disassembled it by simply unscrewing the clip-on piece from the threaded hose end. Inside the chuck was only one part... a 3/16" thick soft white silicone washer that was responsible for sealing the chuck to the valve stem while filling the tire. It was also the part that was preventing the chuck from fully sitting down far enough on the tire's valve stem to push open the tire's pin valve. So, I used a utility knife and shaved about 1/16" off the washer so instead of being 3/16" thick, now it was 1/8" thick. I put the modified washer (with cut side sitting against the brass chuck base not outward towards the tire valve- for better sealing), screwed the chuck back onto the threaded hose end and gave it a try...

United States on Sep 11, 2014

Manny: I bought this because I have trouble getting a good seal on my dual RV back tires valve stem. I have not yet tried it but I think this will work. I have a Sears tire inflator and the chuck's mechanism for making a good seal on the valve stem is the opposite of this inflator. I have clearance problems when I try to use the Sears tire inflator on my dual back tires. I will give this 4 stars. After I tested this on my dual back tires I will revise the rating.

I tested this inflator on my car tires. I am glad I bought this. I found out that my other tire inflator with it's built in gauge was under inflating my tires about 6 psi. The chuck has a good and tight seal on the valve stem. I will give this product 5 stars.

The built in spring loaded chuck lock is very simple to use. Press on the lock insert the chuck as far as it goes on the valve stem, release the lock and you have an air tight seal on tire's valve stem. I also like the inflation trigger, one can gradually adjust the tire inflation to it's recommended psi.

I tried this on my RV with difficult to access valve stems on the back dual tires. It turns out it could not get a good seal on...

United States on Oct 28, 2011

LECH BEDNAREK: I got this to finaly replace the basic ball chuck that came in a set of air tools with my compressor. It good old to have the chuck kept in place with one hand, operate the laver with the other and than have to take it off and check the pressure with a separete gauge few times to inflate one tire properly.

With this inflator it all goes away, and it becomes one hand fast & easy operation.
I have no proplems with clearence to fit the chuck properly on any of my vechicles, but i see it might be a problem for some smaler wheels that have a little clearance around the valves.

The gauge on my inflator is spot on, so again no issue here since some reviewers indacated a problem in this area. Mine is spot on compared to two other gauges I used for a long time. The PSI markings are a little small and spread a little to far, but it's not an issue that will take a star away.

Inflator feels and looks to made well. Should outlast several vechicles or even a compressor in it's life, but we'll see about that.

That said, for the money, it's is one of the best compressor attachments I have got so far.
Five stars with no doubt.

PS: I...

United States on Feb 24, 2011