By: Apex Tool Supply
Are you looking for a reliable replacement part for your Stanley Bostitch, Husky, or other air compressor? Look no further than the Apex Tool Supply AB-9051116 Pressure Reducer! This high-quality product is designed for easy installation and use, and is the perfect size for your compressor. Apex Tool Supply is known for making some of the best Air Compressor Replacement Parts on the market, so you can trust that this pressure reducer will serve you well for years to come.Mrs. Krapf: I guess the moral of the story is you get what you pay for. This is basically a cheaper copy of the stock one on my Senco compressor that was leaking. Pay attention to the guys talking about the body cracking if you try to fully tighten it. The pipe threads are tapped too deeply, so it never really gets tight, and if you run it all the way on it will bottom out and crack the body. The threads for the gauge and air chuck aren't really tapped deeply enough. They go tight after 2-3 turns. So I broke it on install, and it leaked. The only reason it wasn't a total loss was that it was a good enough copy of the one I was replacing that I was able to take the seal out of this one and install it into my leaking one and I ended up with a mutt regulator that works and doesn't leak. Basically I way overpaid for an o-ring and some spare parts, but the compressor is fixed, so good enough. If I had it to do over again I'd just spend the money to get a correct Senco replacement, or just go match up the leaking o-ring at the local hardware store and replace just that. However, I needed the compressor fixed ASAP and I was able to do that, and as my tools are my livelihood I can't say it was a...
United States on Sep 04, 2023
Amzn ShoppersAmzn Shoppers: The media could not be loaded. This was a perfect fit for the Central Pneumatic 3 gallon pancake compressor from HF. Just be warned, it will come installed in a manifold that will not be needed for this application. Put it in a Vice or a pipe wrench and remove the regulator from the manifold. It will then thread right into your compressor after removing the old one. All you need is a Phillips screwdriver for the 6 screws to remove the top cowl, and a crescent wrench for the regulator itself. Worked like a charm and less than 10 bucks! Thanks Amazon!
United States on Aug 14, 2023
Amazon Customer: Replaced old one with this and works great
United States on Aug 07, 2023
Prime member CM: Like some others mention, some might be able to just use the valve and knob instead of replacing the whole valve and body assembly. The Bostitch compressor I needed it for, has the full cover, which makes it hard to get a socket or a wrench on the valve section alone. I watched one video, of a temporary repair tapping out for a 3/8 bolt. This knob here on this brand, can spin all the way out, whereas the older one, had a clip inside so you couldn't so easily. I had to use a punch to drive it out. I had drilled the hole for the 3/8 bolt too large and than tried the 1/8th male pipe thread I than used a 1/8th drain cock, such as those used on the drain for the compressor tank or a radiator. But I did tap a little to far and the threads weren't as tight as they could have been. A thread locker would also be useful. The range of the valve might not close the regulator all the way as this one is still 40 at the stop. But it did open it to the 140 lbs. The drain cock is a left hand thread, so it works the opposite of the original. I plan on using this assembly on a compressor the doesn't have a regulator.
United States on May 07, 2023
miguel a.: Funcionó muy bien en mi compresor, mantiene y regula muy bien la presión
Mexico on Jul 11, 2020
Replacement Pressure Reducer for Stanley Bostitch, Husky, and Porter Cable Air Compressors - Apex Tool Supply AB-9051116 | 2 Pack Replacement A17038 Drain Valve for Porter Cable C2002/C2005 Air Compressors (N286039) | Lefoo 95-125 PSI Air Compressor Pressure Switch Control with 4 Ports and Unloader | |
---|---|---|---|
B2B Rating |
89
|
98
|
96
|
Sale off | $1 OFF | $1 OFF | |
Total Reviews | 72 reviews | 139 reviews | 192 reviews |
Item Weight | 3.8 ounces | 0.08 Pounds | 13.6 ounces |
Style | Manual | ||
Best Sellers Rank | #97,956 in Tools & Home Improvement #49 in Air Compressor Replacement Parts | #49,611 in Tools & Home Improvement #13 in Air Compressor Replacement Parts#121 in Power Tool Replacement Parts | #50,213 in Tools & Home Improvement #14 in Air Compressor Replacement Parts#124 in Power Tool Replacement Parts |
Color | Red | Umber | |
Item model number | AB-9051116 | LF10-4H-1-NPT1/4-95-125 | |
Package Dimensions | 4.25 x 2.8 x 1.97 inches | 3.39 x 0.98 x 0.87 inches | |
Manufacturer | Private Apex Tool Supply | Porter Cable | No |
ASIN | B07WVRS6WZ | B00J5S9A04 | B00QHZPUKC |
Batteries Included? | No | No | |
Customer Reviews | 4.4/5 stars of 745 ratings | 4.7/5 stars of 1,607 ratings | 4.5/5 stars of 3,017 ratings |
Item Package Quantity | 1 | 1 | |
Finish | Iron | ||
Date First Available | August 20, 2019 | March 21, 2014 | March 30, 2009 |
Batteries Required? | No | No | |
Inlet Connection Type | Barb | Butt Weld | |
Part Number | AB-9051116 | N286039 | LF10-4H-1-NPT1/4-95-125 |
Material | Iron | ||
Brand | Apex Tool Supply | PORTER-CABLE | LEFOO |
Melanie Kimball: This was exactly what I needed to fix a 2009 pancake. Works excellently! Thank you for still making these parts for bostitch. I looked on their website and the shipping cost was more than the part. Free shipping with Amazon!
United States on Sep 10, 2023