OEDRO Tri-Fold Truck Bed Tonneau Cover with Upgraded Features

Tinashe C Mariga: Very easy to fit I did it with my lovely daughter.

United States on Oct 19, 2023

Austin yocom: Very nice quality no leaks even in a car wash never had water in the bed very easy to install

United States on Sep 29, 2023

William: When package arrives, package is banded along with brown masking tape protecting banding so banding does not come off. Has quick release tabs on banding or you can cut if off, use caution. First thought my order was a return but I was mistaken, brand new. Use thicker trim piece for truck frame, cut to suit and use thinner trim for side rails. I made mistake running thicker piece from end to end. Which had credit card size height gap.. Cut thinner trim to match outside of tonneau cover and trim, took off truck, for a cpeaner look. Adhesive is satisfactory, after installation it is compressed. Use rubber gasket, shaped like a tube, connected to underside of cover to align cover on rails - run it so that gasket is between two rails raised contours for perfect parrallel alignment.

Adjustment of locking mechanism near tail gate takes time. As you adjust height by turning mechanism then you to manipulate the handle as it hits the truck side wall. Tri fold is super tight, when I was opening it today the center section lifted as I was opening the rear section rrom the back. Had to force, gently, the crease so it would bend.

Would recommend and buy...

United States on Sep 15, 2023

AntonioAntonio: I had a soft roll up Truxedo for years but after the vinyl started cracking from rolling, I wanted to try a hard tonneau cover. I did some research and for the price, I stumbled across this gem from Oedro. Not sure if it's a known main brand name yet (or just an Amazon brand), but it had tons of reviews and I figured I'd give it a shot. Easy to put on, and tie down. Looks incredible in my opinion, though some of the plastic looks like it can initially need some Mother's Back to Black (or similar, FYI the Mother's Back to Black aerosol has been a game changer and life saver for all the plastic on my truck!). The only issue I have so far is with the size of the planks. So I'm assuming that in order to roll out properly and not snag the plastic on each other, each plank from the cab wall that folds outwards is slightly larger than the one before. You can't even really tell on the left side when looking. But the right side is a different story. The different sizes are pretty noticable with just a stop and glance. That's the only thing I wish was different. But, hopefully it goes through the car wash later with not much leaking.

Since it's not a huge known...

United States on Apr 06, 2023

Pearl Dentinger: Fits well, not to hard to install, overall we’re happy with it

Canada on Sep 17, 2021

Kim from San Diego: I have a 2017 Ford XT with a 6' 8" bed. I was a bit concerned with some of the negative feedback, but I found none of it to be true for my install. Keep in mind, this is not a security device, it is a soft top. If you want security pick a hard cover.
It installed in less than 15 minutes. I have a liner. The liner extends about 1/16th of inch below the inside of the inner edge of the metal bedframe. I saw a comment about the rubber seal not lining up with the grooves in the plastic bed liner; that is true. The cover is a fixed width so you set it in a liner groove on one side and it may or may not fall in the liner groove on the other side, but I don't think that is relevant. The seal gasket is about an inch thick uncompressed and if you tighten the brackets you can compress it on whatever surface it lands on (groove, ridge or both). I also saw the comment about the seal 'curling up.' Each of the sections has a piece of gasket. They are separated, and must be to allow the flexibility to fold up. It is pretty simple to hold in in place as you unfold it and lay it flat; you just need to check it before you secure the clamp. I have driven in a heavy...

United States on Mar 15, 2021