By: Capetsma
If you're looking for the perfect aquarium acclimation hatchery incubator for your baby fishes, shrimp, clownfish, and guppies, then the Capetsma Fish Breeding Box is the ideal choice for you. This acrylic fish isolation box comes with suction cups and is easy to assemble and maintain. It's made from high-quality materials and is designed for maximum durability. With this fish breeding tank, you can be sure that your baby fish will be in the best of hands.Schäble AlexanderSchäble Alexander: Mein kleiner Medaka frisst nicht richtig, in der Box kann ich ihn gezielter füttern und beobachten. Ich konnte ihn fast vollkommen stressfrei umsetzen. Evt. wären getönte Scheiben sinnvoller, als eine durchgängig transparent Box.
Germany on Aug 13, 2023
Gerhard Füchsel: Einfach der Hammer
Germany on Aug 11, 2023
Beth BorromeoBeth Borromeo: The product came with a big crack in it, may have been damaged during shipping though. Not a huge deal because it's not supposed to be water tight or anything, but still ugly. But it works and it keeps my tadpole safe from the adult frogs in my fish tank
United States on Aug 03, 2023
tgecks: I use this filled with chaeto as a tiny refugium to reduce nitrates and foster pods for my mandarins, not to mention the benefits they have on the tank overall). The suction cups work when the glass is clean, but even then occasionally let go. The components are buoyancy neutral so will float away in a current; the top occasionally floats off when the top-off device tops it off, so I put a small piece of rock on it. I use a tine 4 LED light magnetically helo to the tank for light and it is thriving and doing its job. Nitrates low, pods all over, and fat mandarins.
United States on Aug 03, 2023
Gabi: Verkäufer zu empfehlen und korrekte Verpackung und pünktlich geliefert
Germany on Aug 02, 2023
BlueGal5658: First,it needs another suction cup at the back, bottom, to hold it level, or the entire box tips up. Then the little plastic molding bits on the sides that hold the bottom plate aren't deep enough, so the dividing plate between mother and fry tilts. As discovered too late, once mother is in and that plate tilts (as it did repeatedly for me), you're out of luck as far as getting it back into place without removing the mother.
United Kingdom on Jul 22, 2023
Thomas: I used this to isolate my aggressive/sick fish. It works very well and it doesn't take much time to add or remove it from a tank. The only issue I've had with it is that my fish like to swim through the gap between the tank and the box, so they get stuck sometimes but they can usually get out on their own. Other than that, great product.
United States on Jun 16, 2023
Klaus R.: Alles soweit OK, wie beschrieben.
Einzig der Deckel hält nicht auf der Schale, weil die Flanken leicht nach innen gebogen sind und deshalb die Abdeckung immer wieder rausschnappt. Könnte man fixen indem man das Plastik erwärmt und etwas biegt, habe aber Angst, dass es dann springt.
Germany on Apr 26, 2023
Rebecca Dye: I didn’t upload any photo because I didn’t want to edit my device settings for photo access but it looks just like the photos depicted its small but it worked well, the suction cups were not initially attached and thus i never used them. I did at some times tape the lid on incase it somehow sunk. Unless strong or determined or multiple fish are looking to be free that shouldn’t be necessary. It worked well overall. the middle layer divider only stayed down well when the little bar divider was also in place below it which was fine. I often didn’t need to use those pieces as I was using it for isolating a aggressive fish or introduction of new fish. I had tried having pregnant fish in there but I never timed it right and I felt bad for them and let them out each time I’d put one of the super pregnant appearing guppies in there after they didn’t give birth within some timeframe of good length. I did however later use the container to hold the baby fry guppies after the fish gave birth in the main tank area and I put some live plants in and it held 20 fry easily and none appear to be able to get out. I’ve seen them try. I had premature baby fry in the main tank at times...
United States on Jun 23, 2022
Fish Breeding Box - Acrylic Isolation Box with Suction Cups - Aquarium Acclimation Hatchery Incubator | Large Fluval Multi-Chamber Breeding and Holding Box | Medium Fluval Multi-Chamber Breeding and Holding Box for Fish | |
---|---|---|---|
B2B Rating |
90
|
96
|
93
|
Sale off | $3 OFF | ||
Total Reviews | 366 reviews | 624 reviews | 202 reviews |
Is Discontinued By Manufacturer | No | No | No |
Material | Acrylic | ||
Date First Available | January 8, 2019 | September 21, 2011 | September 21, 2011 |
ASIN | B07M7H2BK2 | B005QRDCP2 | B005QRDDJ2 |
Manufacturer | capetsma | No | Rolf C. Hagen Corp. |
Style | Modern | Modern | Modern |
Item Dimensions LxWxH | 5.2 x 2.7 x 2.9 inches | 5.8 x 10.7 x 5.7 inches | 5.2 x 6.8 x 5.3 inches |
Specific Uses For Product | Breeder, Isolation, Hatchery | Indoor | |
Color | Clear | Clear | |
Product Dimensions | 5.2 x 2.7 x 2.9 inches; 3.17 Ounces | 5.8 x 10.7 x 5.7 inches; 1.2 Pounds | 5.2 x 6.8 x 5.3 inches; 11.84 Ounces |
Included Components | Suction cups | All items listed in description. | |
Special Feature | Easy to Clean, Durable, Adjustable | ||
Target Species | Fish | Fish | Fish |
Brand | Capetsma | Marina | Marina |
Item Weight | 90 Grams | 1.2 Pounds | 11.84 Ounces |
Sydney F.: I used this for my neo shrimp and they seemed to like it. The babies were not small enough to escape the vents and were able to grow before being released. The suction was a tad iffy, but nothing to write home about. I will definitely be using this over and over again!
United States on Sep 10, 2023