3M Panel Bonding Adhesive: A Strong, Durable Adhesive for Bonding Panels Together

Geo: I had never seen or used this product before. My friend who does body work recommended this to me to install a small replacement panel on a car. Much easier than welding and lest additional work. The results were as good as welding. AMAZING. Highly recommended

United States on Nov 24, 2023

tom mccormick: Bonded great. Pay attention to the amount you're buying. Barely had enough for one side panel. I didn't get the cartridge gun that sells for over 50 dollars because this was a one time deal. Mixing was easy. Waited 24 hours after clamping and the panel wasn't coming off at all. Expensive but it did work.

United States on Aug 26, 2023

The HillsThe Hills: Since it’s completely impossible to judge the size from the official stock photos.

United States on Aug 15, 2023

ザック・バラン: 溶接できないので、パネルボンドを使用しました。トラックですが濡れない場所でしたので。
容量が足りないかもと思ったんですけど、案外いけました。
主剤と硬化剤をうまく押し出せないので、後ろのゴム部分を
直接押して板の上に出して混ぜて使用しました。
接着力は問題ありません。ガッチリつきました。

Japan on Dec 16, 2022

DB: My better headlight cover became detached several years ago due to age and bad tire blow out some time ago. I didn't drive the car at nightuch but because of covid I started in to all the projects I had with it. After the mechanics of the headlight were worked out I started down the path of getting the brackets secured for the cover again. I sanded down to bare metal and SMC, cleaned with soap/water and then alcohol, and applied the panel bond. I can say that at speed with the headlight up, I feel confident the cover won't blow off in to the engine bay.

Also, so many on the vette forums quoted the larger tube. This is perfect with one of the suggested applicator guns and is less then half the price of your doing a little job.

This is a real 3m product that I received as well.

United States on Mar 30, 2021

兄やん: 使い切れるボンドの量が、良かったです。

Japan on Oct 11, 2020

ムン: ...

Japan on Nov 04, 2019

Amazon Customer: Follow directions and you will never use your might welder for joining panels as this holds just as well (or even better) without burning protective coatings which then allows rust to form. You do need to grind any coatings off from the two adjoining surfaces providing a bare metal roughened surface for a good bite. The panel adhesive forms a waterproof barrier where moisture cannot get to the metal surface. If it does, you are not using the product correctly. I use a few sheet metal screws as needed to hold the panel in place until the epoxy cures. A small amount of adheasive should ooz out along the seam edges ensuring that you have used an adequate amount. Then I grind the heads off and roughened the surface around the seam then apply a good quality waterproof short stran filler. Shape, sand and finish as needed. Been using this product for years now. Had a small quarter panel patch repair to do on a 1995 Toyota. This was just the right amount to do the job.

United States on Dec 31, 2018

lizzypoo1985: Great product, just what I need to glue on a cab corner on my jimmy. Proffesional grade, a little expensive but cheaper than the alternative.

Canada on Jun 08, 2017

Amazon カスタマー: ハッチバック車の補強用リアバルクヘッドの固定に使用しました。
補強用リアバルクヘッドは、本来ボルト止めで固定するのですが、数１００ｋｍ走行すると、ボルトが緩んで異音が発生していたのですが、パネルボンドで固定したらガッチリと固定され、ボルト止めのときより剛性アップを体感することができました。ただし、パネルボンドで固定してしまうと、脱着不可能になりますので、そのあたりは自己責任と割り切っております。

Japan on Feb 12, 2015